Differences

This shows you the differences between two versions of the page.

--- en:user_advanced:installation [2018/09/07 03:39] – [Uptodate source code from SVN] anupama
+++ en:user_advanced:installation [2018/09/10 06:35] – anupama
@@ Line 215: / Line 215: @@
 </code>If you're on Mac OS version 10.11/El Capitan, set CFLAGS, CXXFLAGS and JNIFLAGS as follows: \\ <code>export CFLAGS="$CFLAGS -I$JAVA_HOME/include -I$JAVA_HOME/include/darwin"
 export CXXFLAGS="$CXXFLAGS $CFLAGS"
-export JNICFLAGS="$JNICFLAGS $CFLAGS"</code> Since GS3.08, if you're on 64 bit linux, you will also need to add -fPIC to the CFLAGS environment variable: \\ <code>export CFLAGS="-fPIC $CFLAGS"</code>If at any point you run ''source ./gs3-setup.sh'' before compiling, you will have to set up the Java JDK environment again, because the ''gs3-setup'' script will make the included JRE the default Java.
+export JNICFLAGS="$JNICFLAGS $CFLAGS"</code> Since GS3.08, if you're on 64 bit linux, you will also need to add -fPIC to the CFLAGS and CXXFLAGS environment variables: \\ <code>export CFLAGS="-fPIC $CFLAGS"
+export CXXFLAGS="-fPIC $CXXFLAGS"</code>If at any point you run ''source ./gs3-setup.sh'' before compiling, you will have to set up the Java JDK environment again, because the ''gs3-setup'' script will make the included JRE the default Java.
   - The Java Runtime (JRE) included in binaries from Greenstone 3.07 onward is version 7. For 32 bit linux binaries, the included JRE is 32 bit and for 64 bit linux binaries the JRE is 64 bit. //If you have set up a system Java of a version different from the JRE included//, then \\
      * rename the ''packages\jre'' folder to something else, so that when Greenstone runs after compiling, it uses your system Java rather than the old 32 bit JRE v7.
@@ Line 349: / Line 350: @@
   - If you're on Mac OS version 10.11/El Capitan, set CFLAGS, CXXFLAGS and JNIFLAGS as follows: \\ <code>export CFLAGS="$CFLAGS -I$JAVA_HOME/include -I$JAVA_HOME/include/darwin"
 export CXXFLAGS="$CXXFLAGS $CFLAGS"
-export JNICFLAGS="$JNICFLAGS $CFLAGS"</code> Since GS3.08, if you're on 64 bit linux, you will also need to add -fPIC to the CFLAGS environment variable: \\ <code>export CFLAGS="-fPIC $CFLAGS"</code>
+export JNICFLAGS="$JNICFLAGS $CFLAGS"</code> Since GS3.08, if you're on 64 bit linux, you will also need to add -fPIC to the CFLAGS and CXXFLAGS environment variables: \\ <code>export CFLAGS="-fPIC $CFLAGS"
+export CXXFLAGS="-fPIC $CXXFLAGS"</code>
   - In the terminal, you can now finally run ''ant install'' from //the toplevel folder// of your extracted Greenstone 3 installation to start compilation. It can take several minutes. \\ **Note:** If at this stage, compilation fails at Perl's XMLParser with [[http://gentoo.2317880.n4.nabble.com/PREFIX-revolutions-in-the-bootstrapping-world-td181438.html|the error message]] "Only one of PREFIX or INSTALL_BASE can be given. Not both.", then in the same terminal check if the INSTALL_BASE environment variable is set, and if it is, unset it (and PERL_MM_OPT if it was set to this) and re-run ''ant install'':\\ <code>
 > env | grep INSTALL
@@ Line 402: / Line 404: @@
   - If you're on Mac OS version 10.11/El Capitan, set CFLAGS, CXXFLAGS and JNIFLAGS as follows: \\ <code>export CFLAGS="$CFLAGS -I$JAVA_HOME/include -I$JAVA_HOME/include/darwin"
 export CXXFLAGS="$CXXFLAGS $CFLAGS"
-export JNICFLAGS="$JNICFLAGS $CFLAGS"</code> Since GS3.08, if you're on 64 bit linux, you will also need to add -fPIC to the CFLAGS environment variable: \\ <code>export CFLAGS="-fPIC $CFLAGS"
+export JNICFLAGS="$JNICFLAGS $CFLAGS"</code> Since GS3.08, if you're on 64 bit linux, you will also need to add -fPIC to the CFLAGS and CXXFLAGS environment variables: \\ <code>export CFLAGS="-fPIC $CFLAGS"
 export CXXFLAGS="-fPIC $CXXFLAGS"</code>
   - Finally, you can start the steps for building GS3 from SVN: <code>