Differences

This shows you the differences between two versions of the page.

--- en:user_advanced:installation [2023/07/29 09:16] – [Source Distribution] anupama
+++ en:user_advanced:installation [2023/07/29 09:19] – [Source Distribution] anupama
@@ Line 185: / Line 185: @@
   - Now you can finally compile Greenstone 3. Still in your Greenstone installation folder, run ''ant install''.
   - It can take several minutes to compile up.
-  - If you don't already have an imagemagick installed and want to have //imagemagick// in your GS installation, as imagemagick is used to create thumbnail and screenview size images from your full size images, then grab the pre-compiled imagemagick Windows binary from http://trac.greenstone.org/export/head/gs2-extensions/imagemagick/trunk/imagemagick-windows.zip and unzip it into your compiled up GS3 source distribution folder's ''gs2build\bin\windows'' subfolder, so that you end up with an ''imagemagick'' folder in there. Make sure it hasn't created an extra level of an ''imagemagick'' subfolder on extraction, like ''gs2build\bin\windows\imagemagick\imagemagick''. (The dll files should be at the ''gs2build\bin\windows\imagemagick'' level.)
+  - If you don't already have an imagemagick installed on your system and want to have //imagemagick// in your GS installation, as imagemagick is used to create thumbnail and screenview size images from your full size images, then grab the pre-compiled imagemagick Windows binary from http://trac.greenstone.org/export/head/gs2-extensions/imagemagick/trunk/imagemagick-windows.zip and unzip it into your compiled up GS3 source distribution folder's ''gs2build\bin\windows'' subfolder, so that you end up with an ''imagemagick'' folder in there. Make sure it hasn't created an extra level of an ''imagemagick'' subfolder on extraction, like ''gs2build\bin\windows\imagemagick\imagemagick''. (The dll files should be at the ''gs2build\bin\windows\imagemagick'' level.)
@@ Line 204: / Line 204: @@
   - If you wish to compile up the GLI jar files, such as for Remote Greenstone situations, run the following from within the gli folder: ''makejar.bat''.
   - You will need to enable the Administration pages if you want access to them. Do so by editing your Greenstone installation's ''etc/main.cfg'' file. Change the ''status'' field value from ''disabled'' to ''enabled''. In that case, you may also want to change the admin password for the Adminstration pages. Use a DOS prompt to run: ''gsicontrol.bat configure-admin'' which will allow you to (re)set the password for username ''admin'' (the default admin password is the same as the username).
-  - If you don't already have an imagemagick installed and want to have //imagemagick// in your GS installation, as imagemagick is used to create thumbnail and screenview size images from your full size images, then grab the pre-compiled imagemagick Windows binary from http://trac.greenstone.org/export/head/gs2-extensions/imagemagick/trunk/imagemagick-windows.zip and unzip it into your compiled up GS2 source distribution folder's ''bin\windows'' subfolder, so that you end up with an ''imagemagick'' folder in there. Make sure it hasn't created an extra level of an ''imagemagick'' subfolder on extraction, like ''bin\windows\imagemagick\imagemagick''. (The dll files should be at the ''bin\windows\imagemagick'' level.)
+  - If you don't already have an imagemagick installed on your system and want to have //imagemagick// in your GS installation, as imagemagick is used to create thumbnail and screenview size images from your full size images, then grab the pre-compiled imagemagick Windows binary from http://trac.greenstone.org/export/head/gs2-extensions/imagemagick/trunk/imagemagick-windows.zip and unzip it into your compiled up GS2 source distribution folder's ''bin\windows'' subfolder, so that you end up with an ''imagemagick'' folder in there. Make sure it hasn't created an extra level of an ''imagemagick'' subfolder on extraction, like ''bin\windows\imagemagick\imagemagick''. (The dll files should be at the ''bin\windows\imagemagick'' level.)
 </tabbox>